| | DESIGNATION |
REMISE |
PRIX |
DISPO | |
 |
RUT4764 RAM-VB-138
| |
160,60 € HT
192,72 € TTC | Sur
Commande | 
|
|
This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PKLU :Compatible with OEM hand strap Easy insertion and removalCharging functionLockable with keyPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamo
RUT7699 RAM-HOL-HON11PKLU
| |
160,74 € HT
192,88 € TTC | Sur
Commande |
|
|
RUT2253 RAM-S-D-111
| |
161,04 € HT
193,24 € TTC | Sur
Commande |
|
|
RUT6793 RAP-AAPR-WCT-114P-18-UN9U
| |
161,26 € HT
193,51 € TTC | Sur
Commande |
|
|
Sam G Tab S 8.4
RUT0278 RAM-GDS-DOCKL-V2-SAM9U
| |
161,37 € HT
193,64 € TTC | Sur
Commande |
|
|
RUT7129 RAM-GDS-DOCK-SAM62CPU
| |
161,37 € HT
193,64 € TTC | Sur
Commande |
|
|
RUT7744 RAM-GDS-DOCK-D10K-C
| |
161,56 € HT
193,87 € TTC | Sur
Commande |
|
|
This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHLU :
• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC
| | • CE & RoHSAdditional information: Devices shown are not
|
RUT7658 RAM-HOL-ZE32PHLU
| |
161,62 € HT
193,94 € TTC | Sur
Commande |
|
|
RUT0653 RAM-VC-ARM1-7
| |
161,70 € HT
194,04 € TTC | Sur
Commande |
|
|
La station d'accueil RAM Mounts GDS Uni-Conn (14') est une station d'accueil autoportante conçue pour les appareils enfermés dans un IntelliSkin Thin-Case avec des pogo pins arrière.Cette solution peut pivoter à 180 degrés et permettre à l'appareil de s'incliner à 180 degrés, ce qui la rend idéale pour les industries centrées sur le client comme le commerce de détail, l'hôtellerie, la restauration, et plus encore.Elle comprend une plaque d'adaptation pour le montage par perçage, offrant une base stable.L'alimentation est fournie via une connexion USB-C aux pogo pins arrière intégrés dans l'IntelliSkin Thin-Case.Elle prend également en charge un processus d'accueil et de retrait facile :
• L'appareil dans l'étui de protection IntelliSkin est simplement inséré dans la base de la station d'accueil et poussé jusqu'à ce qu'il s'enclenche.Pour le retirer
| | • une simple pression sur le levier libère la tablette.Caractéristiques du produit RAM-GDS-DOCK-D11-14-U3C-GRY :Compatible uniquement avec IntelliSkin Thin-Case (pog
|
RUT7764 RAM-GDS-DOCK-D11-14-U3C-GRY
| |
161,91 € HT
194,29 € TTC | Sur
Commande |
|
|
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU :Compatible with accessori
RUT7636 RAM-HOL-ZE22PLU
| |
161,92 € HT
194,30 € TTC | Sur
Commande |
|
|
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation pr
RUT7649 RAM-GDS-DOCKL-ZE21PDU
| |
162,29 € HT
194,74 € TTC | Sur
Commande |
|
|
RUT6751 RAM-HOL-ZE10PDKLU
| |
162,36 € HT
194,83 € TTC | Sur
Commande |
|
|
RUT8061 RAM-TE-SAM101
| |
162,66 € HT
195,19 € TTC | Sur
Commande |
|
|
RUT5398 RAM-VB-116A
| |
162,80 € HT
195,36 € TTC | Sur
Commande |
|
|
RUT7680 RAM-GDS-SKIN-SAM93-TCB
| |
162,80 € HT
195,36 € TTC | Sur
Commande |
|
|
RUT7349 RAM-VP-SW2F-8-2461
| |
163,68 € HT
196,41 € TTC | Sur
Commande |
|
|
RUT6703 RAP-401-9-BC-202U
| |
163,90 € HT
196,68 € TTC | Sur
Commande |
|
|
RUT4984 RAM-SG-D-111U
| |
164,12 € HT
196,94 € TTC | Sur
Commande |
|
|
RUT2702 RAM-B-189-PIV1-UN11U
| |
164,12 € HT
196,94 € TTC | Sur
Commande |
|
|
RUT1613 RAM-VP-SW1-89-2461
| |
164,34 € HT
197,20 € TTC | Sur
Commande |
|
|
RUT4945 RAM-E-201U
| |
164,56 € HT
197,47 € TTC | Sur
Commande |
|
|
RUT1623 RAM-VP-SW1-47-2461
| |
165,11 € HT
198,13 € TTC | Sur
Commande |
|
|
RUT1663 RAM-VP-SW1-47-240
| |
165,11 € HT
198,13 € TTC | Sur
Commande |
|
|
RUT7668 RAM-GDS-SKIN-SAM88-TCB
| |
165,22 € HT
198,26 € TTC | Sur
Commande |
|
|
RUT1365 RAM-VP-D-SW1-12-246
| |
165,22 € HT
198,26 € TTC | Sur
Commande |
|
|
RUT3464 RAM-GDS-DOCKL-V2-SAM40-AUD1U
| |
165,33 € HT
198,39 € TTC | Sur
Commande |
|
|
RUT3620 RAM-D-111-KNOB9H
| |
165,33 € HT
198,39 € TTC | Sur
Commande |
|
|
RUT7071 RAM-HOL-HON9PD2U
| |
165,33 € HT
198,39 € TTC | Sur
Commande |
|
|
RUT5116 RAM-GDS-DOCKL-V2-SAM35-AUD1U
| |
165,33 € HT
198,39 € TTC | Sur
Commande |
|
|
This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generati
RUT7637 RAM-GDS-DOCKL-ZE20PD2U
| |
165,72 € HT
198,86 € TTC | Sur
Commande |
|
|
RUT2314 RAM-B-152-404
| |
165,77 € HT
198,92 € TTC | Sur
Commande |
|
|
RUT6844 RAM-B-166-SAM9P-2QCCIGU
| |
166,10 € HT
199,32 € TTC | Sur
Commande |
|
|
RUT6748 RAM-CAT-PADDLESPORTS19-50
| |
166,10 € HT
199,32 € TTC | Sur
Commande |
|
|
This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHLU :
• Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS
• CE
| | • RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHLU holder is supplied.
|
RUT7643 RAM-HOL-ZE26PHLU
| |
166,22 € HT
199,46 € TTC | Sur
Commande |
|
|
RUT1491 RAM-VP-SW1-89-240
| |
167,31 € HT
200,77 € TTC | Sur
Commande |
|
|
RUT8035 793442014659
| |
167,33 € HT
200,79 € TTC | Sur
Commande |
|
|
RUT6879 RAM-GDS-DOCKL-V10-SAM67CPU
| |
167,42 € HT
200,90 € TTC | Sur
Commande |
|
|
RUT7368 RAM-GDS-DOCKL-V3CU
| |
167,42 € HT
200,90 € TTC | Sur
Commande |
|
|
RUT5092 RAM-VB-159
| |
167,53 € HT
201,03 € TTC | Sur
Commande |
|
01 43 00 43 08 (lundi au jeudi 8H30 18H30, vendredi 8H30 17H30) Contactez-nous
